Product Review: CocoDrill

Today’s article is brought to you by JM Bullion! If you are looking to get started investing in precious metals, or add some more to your portfolio, give the folks over at JM Bullion a shout.

Yesterday, I wrote about how to use coconut meat to make coconut milk and coconut flour. Making coconut milk is easy, unless the meat is still in the coconut. Getting it and the water out without stress or mess is a far more difficult task.

I’ve seen the islanders using a machete to remove husks in under a minute, as well as using an upright pole to de-husk the nut. It works marvelously, proven techniques used for centuries. However, even when you get to the nut, you still have the trouble of getting a liquid out of a spherical object. This ends up being messy, wasteful, or both.CocoDrill

Enter the CocoDrill.

A simple T handle with a short piece of stainless steel charpeend into a three-point cutting tip, this acts as a coring blade to remove a 1/2 inch plug from the bottom of a coconut. This gives easy access to the water inside.

In all honesty, after getting the hang of it, it takes longer to describe than it does to just do.

Here goes a pictorial though:

CocoDrill and a coconutGet a green coconut. This does NOT work very well (if at all) with a brown coconut. The coconut water is tastier, in my opinion, with a green coconut anyway. Of course, you will also need a CocoDrill.

(Like the bar top I made with tabletop epoxy and stuff found on our local beach?)

CocoDrill and a green coconutLocate the bottom of the green coconut. This is the end away from the stem. This will also be the heavy end.

Think of it this way. The husked coconut is a giant egg, and the part we want is the yolk. While it hangs in the tree, it settles to the bottom of the husk. That help?

CocoDrill and a green coconutPush the CocoDrill into the flat side towards the end of the hard inner shell, aiming for the area with the eyes. Once you reach the harder part, rotate the CocoDrill to cut through the hard shell. A few twists and you should be through.

 

A green coconut with a hole to access the waterRemove the CocoDrill, use the clean out tool to push out the core from the CocoDrill, rinse it, cap it and put it away.Or use it on the next coconut.

As to the coconut, it now has an access hole to allow you to use a straw to drink directly from the source or pour out the water.

I find that by putting a second hole in  the coconut, it makes drinking the water directly without a straw much easier.  Using a finger over the second hole to regulate the amount of air going in, you can easily drink the water without any air glugging or messy splashing – the water pours out in a steady stream.

Split CoconutOnce you’ve removed the water, a single sharp blow from a machete will then cleave the coconut into two pieces. This may take some practice, but without the water inside, it is a simple matter of splitting the nut.

At this point you can use a spoon or a butter knife to remove the meat.

 

CocoDrill Cross sectionIf you look at this picture, you can see the location of the CocoDrill in comparison to the whole nut in a cross section view.

See how the nut itself rests to the lower end of the husk? Take note and plan accordingly.

 

Can you do this with a screwdriver or a drill? Sure! But, is the screwdriver or drill bit stainless? Clean? Handy at all times? Would you stir your sweet tea with a screwdriver or drill bit? This is a consumable product we are trying to get to.

The way I see it, since I am slap in the middle of a LOT of coconut palms (they grow very well here), I’ll just carry my CocoDrill in my day pack as part of my EDC. And since most folks that have coconut palms pay folks to haul them away, I will probably have plenty available for my personal use.

I love free food 🙂

The CocoDrill comes with several options available from the same manufacturer. The CocoDrill alone, with stainless steel drinking straws, or the option I chose, with a pair of nut milk bags. I opted for this so that I could make my own coconut milk.

So if you like in an area with coconuts readily available (and you like coconut water), I’d highly suggest getting one of these.

Or if you are like me,  one for each car.

(For the record, I purchased this with my own funds, and was in no way compensated by the makers of the CocoDrill for writing this review)

Peace,
db

As always, please “like” FloridaHillbilly on Facebook, subscribe to my feed,  follow me on Twitter, add it to Google+, Pinterest, Linkdn, Digg, and/or tell your friends! The more folks that start behaving like ants, the fewer grasshoppers there will be left needing help.

Need something from Amazon (and who doesn’t)? I earn a small commission from purchases made when you begin your Amazon shopping experience here. You still get great Amazon service and your price is the same, no matter what.

6 comments:

  1. DB, since you are the only well informed coconutter I know of… How does one tell if the nut is ready for quality water and when it is ready for coconut meat/milk making? I am assuming that these are different stages of ripeness. Can you tell by looking for size or color?

  2. D – I’m getting one of those! Two reasons I need Coconut Water are:
    Hemingway Tom Collins
    2 oz Hendrick’s or Plymouth gin,
    1 oz lime juice,
    4 oz coconut water,
    2 dashes Angostura bitters

    – Make in glass with ice, garnish with lime wedge.

    and
    Green Isaac’s Special
    2 oz Hendrick’s Gin,
    4 oz green coconut water,
    1 oz lime juice,
    4 drops Angostura Bitters

    – Fill highball glass with ice, add all ingredients, stir, serve. Optional garnish, wedge of lime.

  3. Ordered mine with 3 stainless straws today through the Florida Hillbilly Amazon link. DB and I have tried his on a few and it is the easiest method I have seen.

Leave a Reply to db Cancel reply

Your email address will not be published. Required fields are marked *